| AMI MUCNFL207-21W Flange Block Bearings | D:540 mm; ra max.:4 mm; Calculation factor X:0.39; Da max.:522 mm; r1,2 min.:5 mm; Calculation factor Y0:0.66; B:82 mm; Mass bearing:61.8 kg; Basic dynamic load rating C:520 kN; D1 ≈:472.8 mm; |
| AMI MUCECH206-20NPRF Hanger Unit Bearings | Fillet Radius ra:1.50 mm; D:100.0000 mm; d:45.000 mm; Speed Rating-Open and Shielded-Grease OSG:6700 rpm; Width - Inner Ring B1:39.69 mm; Width - Outer Ring B0:25.0 mm; Accessories:300SWI Non-Filling N; Basic Radial Load Rating-Static SCO:31500 N; Basic Radial Load Rating-Dynamic DC:52700 N; Diameter E:61.1 mm; |
| AMI MUCTBL208-24B Pillow Block Bearings | L:387.35 mm; A2:231.775 mm; Pa:10.5 kN; P60°:94.3 kN; Mass pillow block:31.4 kg; P120°:35.6 kN; Initial grease fill:365.71 g; ba:38.894 mm; P180°:38.3 kN; h:47.625 mm; |
| AMI UCTBL208MZ2B Pillow Block Bearings | Travel:3; Frame Size B:8 in; Frame Size A:4 1/8 in; Shaft C/L Distance F:1 2/5 in; Height G:2.938 in; Bolt Pattern E:6 1/2 in; Frame Accepts These Shaft Sizes (Bearing Bore):20 mm, 25 mm; Bolt Pattern D:2 1/4 in; Bolt Pattern C:0.55 in; Length H:0.500 in; |
| AMI MUCFCF208NP Mounted Units & Inserts | Basic static load rating C0:6.1 kN; Reference speed:28000 r/min; U:10 mm; Designation associated G design radial shaft seal with a low cross-sectional height:G 10x14x3; Limiting speed:32000 r/min; Fw:10 mm; Ew:14 mm; Mass needle roller and cage assembly:0.0025 kg; Basic dynamic load rating C:5.61 kN; Fatigue load limit Pu:0.695 kN; |
| AMI UEFT205-15 Flange Block Bearings | d:75.000 mm; Accessories:Shield & Seal & Snap; Basic Dynamic Radial Load Rating C:95600 N; Oil Speed Rating n2:4300 rpm; D:130.0000 mm; Fillet Radius ra:1.50 mm; Grease Speed Rating n1:3200 rpm; Basic Static Radial Load Rating Co:88000 N; B:41.30 mm; Sealed Speed Rating n3:3200 rpm; |
| AMI UETBL209-28W Pillow Block Bearings | H1:57.15 mm; Da:85.001 mm; PG:1/8 NPT; da:36.513 mm; A2:88.9 mm; Bearing:22209 EK; Ventilation fitting:38174-12; L:209.55 mm; H2:20.637 mm; Cap bolt recommended tightening torque:61 N·m; |
| AMI UCFB201-8NPMZ2 Flange Block Bearings | R2:38.1 mm; End plug (suffix Y):EPR 27; Initial grease fill:481.95 g; Pa:28.5 kN; Bearing:22228 CCK/W33; Ca:77.8 mm; H2:60.325 mm; A2:260.35 mm; Taconite seal:TER 121; P120°:116 kN; |
| AMI UCNST207-23C4HR23 Mounted Units & Inserts | d1:68 mm; d:35 mm; Mass shaft washer:0.14 kg; B:7 mm; r1,2 min.:1 mm; |
| AMI UCST210-32TC Mounted Units & Inserts | D:72.0000 mm; Basic Dynamic Radial Load Rating C:37700 N; d:35.000 mm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:27500 N; Oil Speed Rating n2:8000 rpm; Grease Speed Rating n1:6000 rpm; Sealed Speed Rating n3:6000 rpm; B:30.20 mm; Accessories:Shield & Seal & Snap; |
| AMI UKP205+HA2305 Pillow Block Bearings | d3:440 mm; G3:9 mm; G2:M 6; B5:72 mm; B:55 mm; Locking device:MS 3172-68; B1:288 mm; d1:320 mm; d:340 mm; G:Tr 340x5; |
| AMI MUCST201-8 Mounted Units & Inserts | Sealed Speed Rating n3:2600 rpm; Basic Static Radial Load Rating Co:140000 N; B:68.30 mm; Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:168000 N; d:75.000 mm; D:160.0000 mm; Oil Speed Rating n2:3600 rpm; Accessories:Two Seals; Grease Speed Rating n1:2600 rpm; |